有各種型號,適用于幾乎所有倒置顯微鏡以及直立式顯微鏡。有廣闊可選范圍的腔室和可更換平板適配器,因此儀器非常靈活,可以支持任意細胞培養容器 (培養皿,載波片,多孔板,等) |
| |
CO2 籠式培養器 – 技術規格 |
溫度范圍 | 高于室溫3°C到 50°C |
溫度控制精度 | ±0.1°C |
加熱技術 | 熱氣流 |
控制器類型 | 軟件 / 需要計算機 |
溫度反饋 | 樣本溫度反饋 |
濕度模塊 | 加熱 |
二氧化碳范圍 | 0 到 100% |
|
樣本溫度調節 在培養皿里直接測量溫度,通過一個PID控制器控制溫度:經由風扇把熱空氣吹入顯微鏡周圍的塑料盒子。PID 控制器從參考井中測量溫度并且更新風扇加熱器的溫度,保證樣本溫度穩定在 ± 0.1°C. |  |
CO2 二氧化碳和濕度調節 CO2 二氧化碳在控制器里與空氣混合然后注入微環境腔室,以控制基質的酸堿度. 在整個實驗過程中都可以記錄并控制二氧化碳的濃度水平. 根據需要,第三股氣流可以注入培養腔室。一個加熱濕度模塊可以阻止培養基質的蒸發,并且避免水冷凝在玻璃和塑料表面。. |  |
微環境腔室 微環境腔室用于顯微鏡載物臺并容納樣本。二氧化碳和空氣混合氣流經過預混和預加熱后持續注入腔室。可替換的適配器可以容納任意種類細胞培養容器。 |  |
技術數據 |
熱穩定性 0.1°C |

|
Biaync ay o |
與臺式培養器相當?shù)募?xì)胞增殖情況 |

|
Bianco
|
每日基質蒸發小于2% |

|
FeaturesSeveral windows on the front and side panels allow full and easy access to the microscope. In particular, two openings on the bottom of the front panel give fast access to the focus knob. Additional windows can be realized upon request. | |
|
|
Turn to open hinges allow a one minute removal both of the front and of the upper panel. Once the panels have been removed, the rest of the cage incubator can be easily moved backwards. When needed, the cage incubator can be reassembled and placed again around the microscope in 5 minutes. | |
|
|
Inverted and Upright Microscopes
Mixer or Controller?Okolab Microscope Incubators can be alternatively equipped with two types of CO2 Modules: a Manual CO2 Mixer or a Digital CO2 Controller.
Manual CO2 Mixer It allows to generate COB2B-Air mixtures with an adjustable COB2B concentration in the range 0-15%. Air and COB2B flows are regulated by two floating ball flow meters in the range 0.2 1.7 Nl/min and 0.013 0.13 Nl/min, respectively.
|  |
Digital CO2 Controller It allows to generate a CO2-Air mixture with an adjustable CO2 concentration in the range 0-20%, with an accuracy of ± 5% of CO2 concentration, for instance, if CO2 set point is 5%, accuracy is ± 0.25% . The air flow is regulated by a floating ball air flow meter in the range 0.2 0.8 Nl/min. Sensing Technology A CO2 infrared sensor continuously measures CO2 concentration in the mixed gas stream and a PID closed loop controller gives feedback to a fine valve regulating CO2 flow. Measured value of CO2 concentration is displayed in real time in green . An alarm can be set on CO2 concentration, so that, if CO2 concentration goes below such value, display color turns red and a buzzer turns on. Data Storage The serial RS-232 interface and the CO2 Control Software allow the user to control the unit with a personal computer and to acquire and store concentration data in computer memory. |  |
Digital CO2 Controller's Technical Data
CO2 Concentration Profile

CO2 cycles

Available chambers for MCI
The CO2 Microscope Cage Incubator line is very flexible, thanks to the broad variety of micro-environmental chambers and interchangeable plate adapters available. The aim of the Micro-Environmental chamber is to create a closed environment around the specimen where feeding humid air and CO2.
The choice of the most suitable chamber depends on the type of XY stage (flat mechanical stages, ASI stages and Piezoelectric stages require a different chamber from the other stages).
Each chamber can accommodate any kind of multiwell plate and can be equipped with plate adapters, chosen according to the type of cell culture support used (Petri Dish, glass slide, etc. ). A one screw mechanism allows to change the plate adapters in 30 seconds, so that the same chamber can be used with different cell culture supports.
Every chamber presents holes to allow perfusion tubes' insertion. The Lowered lid allows the high N.A. condensers use.
List of available chambers: |
Universal for Manual Stage: Especially designed to fit on mechanical flat XY stages. It accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top | 

|
| 
|
| |
Universal for Motorized Stage: This model is designed to fit any 160x110mm sized stage (i.e. Ludl BioPrecison and BioPoint, Marzhauser SCAN IM 120x100, Prior H107 and H117), A.S.I. stages and all mechanical flat stages. A dedicated stage insert to fit it into the Nikon TI-S-E motorised XY stage is also available. This chamber model accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top | 

|
| 
|
Universal for ASI - Stage: Especially designed to fit into ASI XY stages. It accepts any kind of multiwell plate (6-12-24-48-96) and can be equipped with plate adapters to accept 35mm petri-dishes, chamber slides and 60 mm Petri-dishes. It can be used both with Long Working Distance and oil-immersion objectives. Back to top | 
|
| 
|
Chamber for Piezoelectric Stage: Special design for Prior NanoScan PZ100 Z Piezo Stage. It allows to use #1 35mm Petri-dish or #1 glass or chamber slide. Back to top | 
|
Lowered lid: Thank to its lowered profile, this special design lid allows to work with high N.A. condensers. It can be mounted on the Universal MEC for Manual Stages and on the Universal MEC for motorized stages, by replacing their standard lid. Back to top | 
|
|
Accessories
Obscuring panels can be assembled with the cage incubator by means of turn to open hinges. They will create a dark environment for your fluorescence experiments. | | |
|
Upon request, a third gas can be fed into the incubating chamber. Different percentages of three gas (typically CO2, O2 and air) are mixed in the control unit and are continuously fed into the incubating chamber to control medium pH and other experimental parameters. | | |
|
Read Temperature Software is available to read incubator temperature and store the data in computer memory. | | |
Back to top |
FOCUS ON THE CO2 MICROSCOPE CAGE INCUBATOR
The space around my microscope is quite limited. Let me define my microscope set-up as non-standard. Can your cage incubator fit my system?
Yes, it can. In this case, one of our application scientists will come to your lab to customize cage drawings.
I would like to feed a third gas stream (i.e. Oxygen) besides CO2 and air in the microscope incubator. Is this possible?
Yes, it is. Please, specify this special request when placing your order.
I was looking for a cage incubator for upright microscopes. Is it available?
Yes, it is. The Microscope Cage Incubator is the solution we offer for upright microscopes.